-14%
MICS-6814 (Air Quality Co, NH3, Nitrogen Oxide Gas Sensor)
Original price was: ₨6,500.00.₨6,150.00Current price is: ₨6,150.00.
MiCS-5524 (CO, Alcohol and VOC Gas Sensor)
Original price was: ₨2,850.00.₨2,450.00Current price is: ₨2,450.00.
Features:
- MiCS5524 CO, Alcohol and VOC Gas Sensor
- Robust MEMS (Micro Electro Mechanical System) Sensor
- Operating Voltage: 4.9V to 5.1V
- Analog Output via Ao pin (voltage increases as amount of any of the detected gases increases)
- For hobby use
- Current Draw: 25 to 35mA
- Works with Arduino, Teensy & Photon boards. Can be used with Raspberry Pi if you can use an Analog to Digital Converter
Description
Suitable Uses:
- Carbon Monoxide Detection
- Natural Gas Leak Detection
- Monitoring Air Quality
- Early Fire Detection
- Breathalyzer (alcohol detection)
- Only 4 Pins: 5V: Power, GND: Ground
- Ao: Analog Output (0V to 5V: as the amount of detected gases increases, voltage increases)
- En: Output Enable (to turn off the sensor for power consumption, send a HIGH 5V signal)
Detection ranges:
- Carbon Monoxide CO: approx 1 to 1000 ppm
- Ammonia: approx 1 to 500 ppm
- Ethanol: approx 10 to 500 ppm
- H2: approx 1 – 1000 ppm
- Methane: approx 1000++ ppm
- Propane: approx 1000++ ppm
- Iso-Butane: approx 1000++ ppm
Reviews (0)
You must be logged in to post a review.
Shipping & Delivery
Related products
AMG8834
Temperature Sensor Digital, Infrared (IR) 14-SMD Module
Product Specifications
| Sensor type | Infrared array sensor | |
| Maximum output current | 10mA | |
| Sensing distance | 7m | |
| Switch mode | digital | |
| Installation type | Surface mount | |
| Number of pins | 14 | |
| Maximum supply current | 4.5 mA | |
| size | 11.6 x 8 x 4.3mm | |
| height | 4.3mm | |
| length | 11.6mm | |
| series | Grid-EYE | |
| Maximum working temperature | +80 °C | |
| Maximum operating supply voltage | 5 V DC | |
| Minimum operating temperature | -20 °C | |
| width | 8mm |
CJ1WTS562 (Temperature Sensor Module Screw Terminal Connection)
Omron Temperature sensor module is suitable for use with cj1 series programmer controllers
Highlights/Features:
Omron Temperature sensor module is suitable for use with cj1 series programmer controllers These temperature sensor units are classified as digital I/O units when considering I/O allocations and will take digital I/O points from the total allocation for a CJ1M CPU. The number of I/O points is DIP switch selectable as follows; configured for 1 - 3 inputs takes 48 digital I/O points, configured for 4 inputs takes 64 digital I/O points and configured for 5 - 6 inputs takes 96 digital I/O points.
KY-028 -Temperature sensor module (Digital)
Product Features:
- Using the NTC thermistor sensor , good sensitivity.
- The comparator output signal is clean, good waveform , driving ability , more than 15mA.
- Adjust the temperature distribution position detection threshold.
- The working voltage: DC 3.3V-5V.
- The output format : digital switching outputs ( 0 and 1 )
- A fixed bolt holes for easy installation.
- Using a wide voltage LM393 comparator.
Motion Detecting Module- Zilog ePIR
Zilog's ePIR is a fully functional motion-detecting single-board computer (SBC). Combined on this board are a Z8 Encore! XP MCU, and a Murata passive infrared (PIR) sensor, which is shielded by a Fresnel lens. Taking advantage of the processing capabilities of the Z8 MCU, the ePIR uses a powerful new statistical processing method to provide exceptional motion detection performance.
MQ-7 (Carbon Monoxide Gas Sensor Module)
MQ-7 Carbon Monoxide Gas Sensor Module is used to detect Carbon Monoxide (CO) concentration, it can detect CO-gas concentrations anywhere from 20 to 2000ppm. This sensor has a high sensitivity and fast response time. The module outputs a voltage from 0 to 5V relative to the CO concentration. The sensor can operate at temperatures from -10 to 50°C and consumes less than 150 mA at 5 V.
TTP 223B (Touch Thumb Sensor Module)
Product description:
This is a simple touch sensor module. You can use it to replace a traditional push button. Using the TTP223 touch detector IC It measures the capacitance of a metallic pad. It can detect the change in capacitance when a finger is near it. This is the same technology used in the iPhone touch screen.This little sensor can "feel" people and metal touch and feedback a high/low voltage level. Even isolated by some cloth and paper, it still can feel the touch. And the sensitivity well decrease as isolation get thick.
Reviews
There are no reviews yet.