You must be logged in to post a review.
GY-652 (Air Pressure + Magnetic Field Sensor Module)
This is the GY-652 Sensor Module with HMC5983 and BMP180 Electronic Compass which enables us to measure Atmospheric Pressure and Magnetic Fields about 3 axes along with Pressure.
– Model: GY-652
– The use of chip: HMC5983 + BMP180
– Power supply :3-5v (internal low dropout regulator)
– Communication modes: standard IIC communication protocol)
– Magnetic field range: ± 0.88 to ± 8.1 gauss
– Pressure Range :300-1100hPa
– Chip 12bit AD converter, 16-bit data output
– Machine welding process to ensure quality
– Size: 13mm * 14mm (standard pitch 2.54mm)
– for ARDUINO test code
Categories: Barometric Pressure Sensor, Sensor Modules
Related products
BMP280 (I2C/SPI Digital Barometric Pressure Sensor Module for Arduino)
The BMP280 sensor is an environmental sensor with temperature, barometric pressure that is the next generation upgrade to the BMP085/BMP180/BMP183. This sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI.
Features:
- Pressure range: 300 ~ 1100hPa (altitude 9000 m ~ -500 m); - Working voltage: 1.71 - 3.6VDC; - Low power consumption: 4μA; - High precision: at low-power mode, the resolution is 0.06hPa (0.5 meters); - Temperature output; - Communication interface: I2C or SPI; typical application: - GPS precise navigation (dead reckoning, the upper and lower bridge detection, etc.); - indoor and outdoor navigation; - The weather forecast; - The vertical velocity indication (rise / sink speed); Note: You need to add 5V to 3.3V level converter circuit between Arduino UNO R3 and the module.CJ1WTS562 (Temperature Sensor Module Screw Terminal Connection)
Omron Temperature sensor module is suitable for use with cj1 series programmer controllers
Highlights/Features:
Omron Temperature sensor module is suitable for use with cj1 series programmer controllersThese temperature sensor units are classified as digital I/O units when considering I/O allocations and will take digital I/O points from the total allocation for a CJ1M CPU. The number of I/O points is DIP switch selectable as follows;configured for 1 - 3 inputs takes 48 digital I/O points, configured for 4 inputs takes 64 digital I/O points and configured for 5 - 6 inputs takes 96 digital I/O points.HTG3515CH- (Voltage Output Temperature and Humidity Sensor)
Voltage Output Temperature and Humidity Sensor HTG3515CH
Relative Humidity and Temperature Module
SPECIFICATIONS:
- Suitable for small bulk assembly
- Product free from Lead, Cr (6+), Cd and Hg. Compliant with RoHS
- Full interchangeability. Better than +/-3%RH and +/-0.25°C
- Humidity calibrated within +/- 3% RH @ 55% RH
- Temperature measurement through NTC direct output
Based on the rugged HUMIREL humidity sensor, HTG3515CH is a dedicated humidity and temperature plug and play transducer designed for OEM applications where a reliable and accurate measurement is needed. Direct interface with a micro-controller is made possible with the module’s humidity linear voltage and direct NTC outputs. HTG3515CH is designed for high volume and demanding applications. MS554C (Digital Barometric Waterproof Pressure Sensor)
Sharp IR Long Range Sensor – 20 cm to 150 cm
- Infrared range finder 20cm(~8") to 150cm (~60")
- Analog interface
SHT31 (Digital Temperature and Humidity Sensor Module)
General Features:
- Highly reliable, accurate and quick response time
- I2C interface
- Well calibrated, linearized, compensated for digital output
- Highly abstracted development library
- Input voltage (VCC): 3.3 volts or 5 volts
- I/O Logic Level : 3.3 volts or 5 volts based on VCC
- Operating Current : 100 μA
- Operating Temperature : -40–125 ℃
- Temperature Sensor Range : -40–125 ℃, with ±0.3°C accuracy
- Humidity Sensor Range : 0% - 100%(Relative Humidity), with ±2% accuracy
- Sensor Chip : SHT31
- I2C
T000220 (Arduino TinkerKit Touch Sensor Module)
This TinkerKit sensor is a touch sensitive device that provides an output when it detects skin contact. The sensor is connected to an Arduino board via a TinkerKit Shield to form part of the TinkerKit modular prototyping system.
- Based on a QT 100A single touch controller
- On-board-signal amplifier
- Green LED for correct power indication
- Yellow LED whose brightness depends on the values output by the module
Reviews
There are no reviews yet.