You must be logged in to post a review.
SW-18010P (Vibration Sensor Module)
1. when the product does not work, the vibrating switch is turned off, the output of the high output, the green light does not shine through
2. when the product shock, vibration switch is turned on instantly, output low output, green indicator light
3. the output can be directly connected to the microcontroller through the microcontroller to detect high and low, thereby determining whether there is a vibration in the environment, playing a role in the police
Pin description:
- VCC: 3-5V DC
- GND: min/ground/gnd
- DO: digital output (sensitivity can be controlled with the potentiometer)
- AO: analog output
Categories: Sensor Modules, Vibration Sensor Modules
Related products
GY-AMG8833 (IR 8×8 infrared camera array temperature sensor module)
Motion Detecting Module- Zilog ePIR
Zilog's ePIR is a fully functional motion-detecting single-board computer (SBC). Combined on this board are a Z8 Encore! XP MCU, and a Murata passive infrared (PIR) sensor, which is shielded by a Fresnel lens. Taking advantage of the processing capabilities of the Z8 MCU, the ePIR uses a powerful new statistical processing method to provide exceptional motion detection performance.
MQ-6 LPG Gas Sensor Module
This is a simple-to-use liquefied petroleum gas (LPG) sensor, suitable for sensing LPG (composed of mostly propane and butane) concentrations in the air. The MQ-6 can detect gas concentrations anywhere from 300 to 10000ppm. This sensor has a high sensitivity and fast response time. The sensor’s output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater coil with 5V, add a load resistance, and connect the output to an ADC.
MQ-7 (Carbon Monoxide Gas Sensor Module)
MQ-7 Carbon Monoxide Gas Sensor Module is used to detect Carbon Monoxide (CO) concentration, it can detect CO-gas concentrations anywhere from 20 to 2000ppm. This sensor has a high sensitivity and fast response time. The module outputs a voltage from 0 to 5V relative to the CO concentration. The sensor can operate at temperatures from -10 to 50°C and consumes less than 150 mA at 5 V.
T000220 (Arduino TinkerKit Touch Sensor Module)
This TinkerKit sensor is a touch sensitive device that provides an output when it detects skin contact. The sensor is connected to an Arduino board via a TinkerKit Shield to form part of the TinkerKit modular prototyping system.
- Based on a QT 100A single touch controller
- On-board-signal amplifier
- Green LED for correct power indication
- Yellow LED whose brightness depends on the values output by the module
TMP006 (Contact-less Infrared Temperature Measurement)
The TMP006 works with 3v to 5v, so it can be used with most microcontrollers without the need for a level shifter. It connects via the i2c bus and is addressable so you can have up to 8 TMP006 sensors on the same bus.
Features:
- 20mm x 20mm (board w/o headers)
- Uses I2C 7-bit addresses between 0x40 and 0x47, selectable with jumpers
- Interface Type : I2C Arduino driver module
TTP224 (4 Channel Digital Capacitive Touch Sensor Button Switch Module For Arduino)
TTP229-LSF (Capacitive Touch Keypad Module)
Features:
- On board 8 capacitive touch keys and 1 linear capacitive sensor
- Features TONTEK TonTouch touch pad detector IC TTP229-LSF, supports up to 16 keys with adjustable sensitivity and built-in LDO
- The system recalibrates automatically when all keys are not detected touch more than about 4 seconds
- Customizable functions:
- 8 keys or 16 keys option
- 8 individual outputs or batch production
- Single-key or multi-kye feature
- Sampling rate and duration of sampling in sleep mode
- The maximum key is on time
Reviews
There are no reviews yet.