WizFi220 (WiFi)
WizFi220 is a Wi-Fi module that provides the robust and stable Wi-Fi connectivity. WizFi220 performs all functions for Wi-Fi connectivity and TCP/IP processing. All you have to do is just sending commands to the module via serial interface.
WizFi220 is all compatible with WizFi210 in hardware & software, but it has the external power amplifier for the longer communication.
Description
Description:
The WizFi220_CA is an ultra low power serial to WiFi module with power amplifier and on-board Chip Antenna. The module provides serial UART interface which enables connection to any embedded design utilizing and 8/16/32-bit micro-controller via simple commands. The module supports data rates up to 11 Mbps, and is compliant with 802.11b. The Serial to Wi-Fi embedded software allows devices and appliance manufacturers to easily add WiFi capabilities to their products with minor impact on the host micro-controller firmware. The WizFi220 provides all the hardware and software necessary to quickly set up a serial (UART) based link to a PC or external micro-controller.
Features:
- Brings Wi-Fi connectivity to any device with a micro-controller and serial HOST interface (UART)
- Quick Booting Time : under 20mSec
- Minimal Serial to Wi-Fi “driver ” footprint on host microcontroller and minor changes to existing host MCU firmware
- Offloading of smaller host microcontrollers from the Wi-Fi and TCP/ IP networking
- Simple AT commands for configuration and data communication
- On-board Chip antenna
- DHCP/Static IP, TCP/UDP, Server/Client, DNS, ARP
- Easy device provisioning through our utility or Wi-Fi Protected Set-up (WPS)
- Ultra low power consumption through dynamic power management
- Operates with standard 802.11 b/g/n access points at speed up to 11 Mbps (802.11b)
- Security protocols (WEP, WPA, WPA2-PSK, Enterprise, EAP-FAST, EAP-TLS, EAP-TTLS, PEAP)
- DSSS and CCK modulation
- Rich I/O interfaces (SPI, UART, GPIO, I2C, ADC, JTAG)
- Low power modes, Alarm Input for wake-up
- High-throughput hardware AES and RC4 encr yption/decryption engines
- Size 32 x 23,5 x 2,9 mm
- CE, FCC, KCC certified
- Limited AP Feature (Direct Connection to iPhone, iPad and Android-Phone without AP)
- 3.3V power source
Specification:
- Radio Protocol: IEEE 802.11b/g/n Compatible
- Supported Data Rates: 11, 5.5, 2, 1 Mbps (IEEE 802.11b)
- Modulation: DSSS and CCK
- RF Operating Frequency: 2.4 – 2.497 GHz
- Antenna Options: Chip antenna
- Networking Protocols: UDP, TCP/IP (IPv4), DHCP, ARP, DNS, HTTP/HTTPS Client and Server(**)
- Power Consumption Standby: 34μA
- Receive: 125mA
- Transmit: 290mA
- RF Output Power (Typical): 17dBm ± 1.5dB
- Security Protocols: WEP, WPA/WPA2?PSK, Enterprise (EAP-FAST, EAP-TLS, EAP-TTLS, PEAP)(**)
- I/O Interface: UART, SPI(**), I2C(*), WAKE, ALARM, GPIOs
- Power Source: 3.3V
- Dimensions: 32 x 23.5 x 3 mm
Reviews (0)
You must be logged in to post a review.
Shipping & Delivery
Related products
Arduino Ethernet Shield w/o PoE (Wiznet W5100)
(Get A latest Price)
The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100 ethernet chip providing a network (IP) stack capable of both TCP and UDP. The Arduino Ethernet Shield supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet via a standard RJ45 Ethernet jack using the shield.
Arduino MEGA 2560 R3 (ATMEGA2560-16AU MCU)
Overview
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560 (datasheet). It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega is compatible with most shields designed for the Arduino Duemilanove or Diecimila.
ESP8266 ESP-12F WiFi module
The module has the ability to run independent of a host controller.
The ESP8266 Serial/UART to WiFi module is a great way to connect your Arduino or other microcontroller projects to a WiFi network.
You can proceed to create your next internet of things (IOT) project with affordable network connectivity by implementing this module into your design.
The ESP8266 has 3.6V max tolerant I/Os so you will need a logic level converter to connect it with higher voltage devices such as Arduino.
The ESP8266 requires 3.3V power so you may need a 3.3V voltage regulator to provide the correct voltage, depending on your setup.
ESP8266 NodeMCU Lua WiFi Development Board
The NodeMcu is an open-source firmware and development kit that helps you to Prototype your IOT product within a few Lua script lines.
Generals:
- The Development Kit based on ESP8266, integates GPIO, PWM, IIC, 1-Wire and ADC all in one board.
- Power your developement in the fastest way combinating with NodeMCU Firmware!
- USB-TTL included, plug&play
- 10 GPIO, every GPIO can be PWM, I2C, 1-wire
- FCC CERTIFIED WI-FI module（Coming soon）
- PCB antenna
ESP8285 ESP-M3 (Transparent Serial Port wireless WiFi control module)
ESP8285 = ESP8266 + 1M Flash, so it can withstand high temperatures up to 125 degrees Celsius! and the original ESP8266 program source code can be used for transplantation.
ESP-M3 core processor module using cost-effective chip ESP8285. The chip integrates the advanced Tensilica version of the L106 diamond bit core with SRAM on-chip in a smaller package. ESP8285 has a complete Wi-Fi network function, both can be used independently, can also be used as a slave by other running MCU hosts.when the ESP8285 hosting application, it can be started directly from the external Flash. built-in cache memory facilitates system performance and optimizes storage systems. in addition, ESP8285 only through the SPI / SDIO interface or I2C / UART port can be used as a Wi-Fi adapter connection, applied to any micro-controller-based design.
WiFly RN-171
Features:
- Ultra low power for battery powered applications
- Firmware configurable transmit power: 0dBm to +12dBm
- Hardware interfaces: UART
- Supports Adhoc and infrastructure networking modes
- User programmable GPIO & ADCs
- Real-time clock for time-stamping, auto-sleep, and auto-wakeup modes
- Run directly from batteries or regulated power supplies
- Configuration over serial or wireless interface using simple ASCII commands
- Over the air firmware upgrade
- Secure Wi-Fi authentication schemes (WEP/WPA/WPA2)
- Full onboard TCP/IP stack (no external drivers required)
Reviews
There are no reviews yet.