Arduino Sheilds
Arduino Ethernet Shield w/o PoE (Wiznet W5100)
(Get A latest Price)
The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100 ethernet chip providing a network (IP) stack capable of both TCP and UDP. The Arduino Ethernet Shield supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet via a standard RJ45 Ethernet jack using the shield.
Arduino Shield RAMPS-FD for Arduino Due 3D printer controller
When you use Arduino Due as the controller of your 3D Printer, you may find the RAMPS1.4 is not compatible with DUE.As you know the Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3, the importance is the Atmel SAM3X8E chip used on the Due operates at 3.3V,worse applying 5V to the Due's inputs will likely damage the chip.
So we create a new RAMPS variant which is compatible with the Due to replace Ramps 1.4.
Arduino WiFi Shield with Integrated Antenna A000058
Overview:
The Arduino WiFi Shield connects your Arduino to the internet wirelessly. Connect it to your wireless network by following a few simple instructions to start controlling your world through the internet. As always with Arduino, every element of the platform ā hardware, software and documentation ā is freely available and open-source. This means you can learn exactly how it's made and use its design as the starting point for your own circuits.- Requires and Arduino board (not included)
- Operating voltage 5V (supplied from the Arduino Board)
- Connection via: 802.11b/g networks
- Encryption types: WEP and WPA2 Persoanl
- Connection with Arduino on SPI port
- on-board micro SD slot
- ICSP headers
- FTDI connection for serial debugging of WiFi shield
- Mini-USB for updating WiFi shield firmware
Base Shield V2
Arduino Uno is the most popular Arduino board so far, however it is sometimes frustrating when your project requires a lot of sensors or LEDs and your jumper wires are in a mess. The purpose of creating the Grove ā Base Shield is to help you getting rid of bread board and jump wires. With the rich grove connectors on the base board, you can add all the grove modules to the Arduino Uno very conveniently!
BLE Shield Bluetooth expansion board compatible with Arduino
Bluetooth Shield for Arduino (Master Slave)
CC3000 WiFi Shield for Arduino
CC3000 is a fully-equipped wireless network processor, which simplifies the execution of Internet connectivity . SIMPLELINK WIFI can greatly reduce the host microcontroller (MCU) software requirements , making use of any low-cost and low- power MCU embedded applications can be the ideal solution
Wireless Network Processor : IEEE802.11b / g
Embedded IPV4TCP/IP stack
The radio industry\ās best performance:
Tx Power : 11MBPSj for +18 DBM, CCK
RX Sensitivity :-86DBM, 8% packet error rate (PER), 11MBPS
Memory package with a compact , low processing millions of instructions every second (MIPS), low-cost microcontroller to work together :
2K Bytes Flash
250 bytes of RAM
Operating temperature range : -20 to 70 degrees
Four Channel Relay Shield 5V Module for Arduino
GPS Shield with Data Logger (SD Card) for Arduino UNO +
A GPS module breakout board designed for Global Positioning System receiver with SD interface. It is easy to use for logging the GPS data into SD card. 5V/3.3V compatible operation voltage level make it compatible with Arduino UNO, Mega 2560 or Leonardo boards, leaf maple, IFlat32 and other arduino compatible boards. It is a compact, high performance, with low power consumption GPS engine board. It uses ubloxās NEO-6M GPS SiRF Star III chipset which can track up to 20 satellites at a time and perform fast TTFF in weak signal environments.
MICO Shield for Arduino
MICO Shield make it easy for Arduino users to create projects using cell phones. MICO can answer and place calls, present caller with voice prompt and accept touch tone commands.
MICO connects to a cell phone via audio jack and it has circuits to detect and answer calls. It then uses pre-recorded voice prompts to present information and options to callers, and touch-tone telephone keypad entry to gather responses. Responses can then be used to control lights, motors and other actuators, and get readings of temperature, wind speed, proximity and other sensors. The caller can be just a few feet or hundreds of miles away!
MICO is an acronym for Mobile Interactive voice response & COntrol. The word Mico in Portuguese means small monkey. Itās pronounced āmee coā.
Micro SD TF Memory Card Shield Module SPI For Arduino
Features:
Supports Micro SD cards, Micro SDHC card(Micro SD<=2G, Mirco SDHC<=32G).
Level conversion circuit board that interfaces level for 5V or 3.3V.
Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board.
It is a standard SPI communication interface.
4 M2 screw positioning holes for easy installation.
Motor Drive Shield (L293D) for Arduino
L293D is a monolithic integrated, high voltage, high current, 4-channel driver
- Can drive 4 DC motors or 2 stepper motors or 2 Servo.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection.
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
- 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 10V DC.