Sensor Modules
BMP280 (I2C/SPI Digital Barometric Pressure Sensor Module for Arduino)
The BMP280 sensor is an environmental sensor with temperature, barometric pressure that is the next generation upgrade to the BMP085/BMP180/BMP183. This sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI.
Features:
- Pressure range: 300 ~ 1100hPa (altitude 9000 m ~ -500 m); - Working voltage: 1.71 - 3.6VDC; - Low power consumption: 4Ī¼A; - High precision: at low-power mode, the resolution is 0.06hPa (0.5 meters); - Temperature output; - Communication interface: I2C or SPI; typical application: - GPS precise navigation (dead reckoning, the upper and lower bridge detection, etc.); - indoor and outdoor navigation; - The weather forecast; - The vertical velocity indication (rise / sink speed); Note: You need to add 5V to 3.3V level converter circuit between Arduino UNO R3 and the module.
CAP1188 (8 Capacitive Touch Sensor Module SPI/I2C Captouch LED for Arduino)
CJ1WTS562 (Temperature Sensor Module Screw Terminal Connection)
Omron Temperature sensor module is suitable for use with cj1 series programmer controllers
Highlights/Features:
Omron Temperature sensor module is suitable for use with cj1 series programmer controllers These temperature sensor units are classified as digital I/O units when considering I/O allocations and will take digital I/O points from the total allocation for a CJ1M CPU. The number of I/O points is DIP switch selectable as follows; configured for 1 - 3 inputs takes 48 digital I/O points, configured for 4 inputs takes 64 digital I/O points and configured for 5 - 6 inputs takes 96 digital I/O points.
CJMCU-175 (Digital Temperature Sensor Module)
General Features:
CJMCU-175 Digital Temperature Sensor TMP175 27 Address
Digital output: SMBusTM, two-wire and I2C interface compatibility
Resolution: 9 to 12 digits, user selectable
Wide supply voltage range: 2.7V to 5.5V
TMP175 allowing up to 27 devices on a bus member.
It is a negative temperature desired coefficient thermistor (NTC) and positive temperature coefficient (PTC) for generation
The device provides a typical Ā±1Ā°C accuracy without calibration or external component signal conditioning .
The on-chip 12-bit analog -to- digital converter (ADC) provides resolution down to 0.0625Ā°C.
CJMCU-6002 (Sun Ultravoilet Spectral Intensity Sensor)
Solar Ultraviolet spectral sensor of intensity of analog voltage
Power range: +2.7-5.5VDC
Output signal: analog voltage
The CJMCU-6002 UV sensor module expands the photosensitivity spectrum. It uses an ultraviolet photodiode to detect light in the 240 ā 370nm range (including most of the spectra of UVA and UVB ).
Current Transformer- ZMCT118F 30A
(Ask For A Quotation)
A current transformer (CT) is used for measurement of alternating electric currents. When current in a circuit is too high to apply directly to measuring instruments, a current transformer produces a reduced current accurately proportional to the current in the circuit, which can be conveniently connected to measuring and recording instruments. A current transformer isolates the measuring instruments from what may be very high voltage in the monitored circuit.
Features
- Small size
- High accuracy, and good consistency,for current and power measurement
- ZMCT118F can measure the AC current upto 30 amps
- Output proportional to AC current
DHT11 (Temperature and Humidity Sensor Module)
DHT11 Temperature and Humidity Sensor Module with LED Power Supply Indicators
Features:
- Can detect surrounding environment of the humidity and temperature
- DHT11 sensor adopts
- Humidity measurement range: 20%-95%, humidity measurement error: +-5%
- Temperature measurement range: 0 -50 ;measurement error: +-2 degrees
- Working voltage 3.3 V-5 V
- Output form: digital output
- Has fixed bolt hole and easy installation
- PCB size: 3.1cm x 1.4cm
DHT22- (Temperature and humidity sensor)
Product description:
The DHT22 module is designed to measure the temperature and humidity of the atmosphere. The difference from the younger model (DHT11), The DHT22 has a wide range and a high precision determination of temperature and humidity. The sensor works on the OneWire bus, which makes it possible to connect it to the Arduino only three wires ( two of which are POwer supply). Low power consumption allows you to install it on stand-alone devices.
DSM501A (Dust Sensor Module)
GH-311RT (Ultrasonic Distance Ranging Sensor)
GO2Y0A21YK
GO2Y0A21YK
Infrared distance measuring sensor (including dedicated data line)Technical Parameters:
- Model : GP2Y0A21YK (GP2D12 upgrade)
- Voltage: 4.5-5. 5V
- Current: 33-40mA
- Port: Analog
- Detection distance: 10-80cm
- Data line: 3P 20cm
- Wire: 24# American standard line
- Interface: 3P DuPont SVG compatible Arduino sensor expansion board
GP2Y0D815Z0F (Digital Distance Measuring Sensor 15cm)
Feature summary:
- operating voltage: 2.7 V to 6.2 V
- average current consumption: 5 mA (typical)
- distance measuring range for GP2Y0D815Z0F: 0.5 cm to 15 cm (0.2" to 6")
- output type: digital voltage
- steady state response time: 2.56 ms typical (3.77 ms max)
- module size: 21.6 x 8.9 x 10.4 mm (0.85" x 0.35" x 0.41")
- weight without header pins: 1.3 g (0.05 oz)