Sensor Modules
MB1403 (USB Ultrasonic Range Finder-MaxSonar-EZ0)
Overview:
- USB interface
- Resolution of 1 mm
- Multi-sensor operation
- ~250mS between range readings
- Maximum Range of 5000 mm (196 inches)
- 42kHz Ultrasonic sensor measures distance to objects
- RoHS compliant
- Virtually no sensor dead zone, objects closer than 30 cm range as 30 cm
- Small, light weight module
- Designed for easy integration into your project or product
- Widest beam of the HRUSB-MaxSonar-EZ sensors
- Great for people detection applications
MiCS-5524 (CO, Alcohol and VOC Gas Sensor)
Features:
- MiCS5524 CO, Alcohol and VOC Gas Sensor
- Robust MEMS (Micro Electro Mechanical System) Sensor
- Operating Voltage: 4.9V to 5.1V
- Analog Output via Ao pin (voltage increases as amount of any of the detected gases increases)
- For hobby use
- Current Draw: 25 to 35mA
- Works with Arduino, Teensy & Photon boards. Can be used with Raspberry Pi if you can use an Analog to Digital Converter
MICS-6814 (Air Quality Co, NH3, Nitrogen Oxide Gas Sensor)
The MiCS-6814 is a 3 sensor device suitable for gas leak detection and outdoor air quality monitoring. MiCS-6814 can detect many unhealthful gases, and three gases can be measured simultaneously due to its multi channels, so it can help you to monitor the concentration of gases where you expect the existence of more than one gas.
Detectable gases:
- Carbon monoxide CO 1 ā 1000ppm
- Nitrogen dioxide NO2 0.05 ā 10ppm
- Ethanol C2H5OH 10 ā 500ppm
- Hydrogen H2 1 ā 1000ppm
- Ammonia NH3 1 ā 500ppm
- Methane CH4 >1000ppm
- Propane C3H8 >1000ppm
- Iso-butane C4H10 >1000ppm
ML8511 (Analog Output Ultraviolet Sensor)
Features:
- Optical sensor to UV-A and UV-B
- Realize equalization of an output voltage by trimming
- The analog voltage output proportional to UV light intensity
- Low current operation ( 300ĀµA Typ. ) and low standby current ( 0.1ĀµA Typ. )
- The TSV-CSP version is under development for the further small size package( 2.1 Ć 1.8mm )
Motion Detecting Module- Zilog ePIR
Zilog's ePIR is a fully functional motion-detecting single-board computer (SBC). Combined on this board are a Z8 Encore! XP MCU, and a Murata passive infrared (PIR) sensor, which is shielded by a Fresnel lens. Taking advantage of the processing capabilities of the Z8 MCU, the ePIR uses a powerful new statistical processing method to provide exceptional motion detection performance.
MPL115A1 (Barometric Pressure Sensor Breakout)
Now mounted on a breakout board, the MPL115A1 is a digital barometer that uses MEMs technology to give accurate pressure measurements between 50kPa and 115kPa. We stock the SPI interface version of the sensor. Average current consumption is 10ĀµA at one measurement per second.
The sensor outputs both temperature and pressure readings on the SPI bus. See page 3 of the datasheet for information on how to take readings from the pressure sensor.
FEATURES:
- Wide supply voltage range
- -40Ā°C to 105Ā°C maximum temperature range
- Low power consumption
- kPa accuracy
MPL3115A2 (I2C Barometric Pressure/Altitude/Temperature Sensor)
-Control mode: 2mA
-Low power mode: 8.5Ī¼A , 1Hz sampling
-Compensation of output data:
20 bit pressure data, output per unit Pascal
20 bit height data, output per unit of meter
12 bit temperature data, output per unit degree with
-I2C digital output interface
-2 * programmable pin interrupt
-Contained in 32 selective FIFO buffers
MQ-135 (Air Quality Control Gas Sensor)
MQ-137 (Ammonia (NH3) Sensor Module)
Sensitive material of MQ-137 gas sensor is SnO2, which acts as lower conductivity in clean air. When the target combustible gas exist, the sensor's conductivity is more higher along with the gas concentration rising. Please use simple electrocircuit, Convert change of conductivity to correspond output signal of gas concentration.
MQ137 gas sensor has high sensitivity to Ammonia, also to other organic amine. The sensor could be used to detect different gases which are contained Ammonia. It is a low cost module and suitable for different environmental protective application.
MQ-2 (Smoke sensor-HBO, LPG, Alcohol, Propane, Hydrogen, Methane and Carbon Monoxide)
MQ2 Smoke Gas Sensor Module is a general purpose gas sensor and this Sensor is used to detect the gas leakage of LPG, Smoke, Alcohol, Propane, Hydrogen, Methane and Carbon Monoxide concentrations ranging from 200 to 10000 ppm.
- MQ-2 Gas Sensor Module LPG, Smoke, Alcohol, Propane, Hydrogen, Methane and Carbon Monoxide Detection
- Dual signal output (analog output, and TTL level output)
- The gas, natural gas, city gas, smoke better sensitivity
- With a long service life and reliable stability
- Rapid response and recovery characteristics
