-22%
1-Channel Relay Module |DC 24V 30A| High Low Level Trigger with Optocoupler Isolation for PLC Automation, Equipment Control, Industrial Control
Original price was: ₨650.00.₨550.00Current price is: ₨550.00.
8-Channel Relay Module (24VDC)| High/Low Level Trigger with Optocoupler Isolation Load DC 30V/10A AC 250V/10A for PLC
Original price was: ₨1,850.00.₨1,550.00Current price is: ₨1,550.00.
8-Channel Relay Module (12VDC)| High/Low Level Trigger with Optocoupler Isolation Load DC 30V/10A AC 250V/10A for PLC
Original price was: ₨1,850.00.₨1,450.00Current price is: ₨1,450.00.
Introduction:
- Module uses high-quality relay, normally open interface maximum load: AC 250V / 10A, DC 30V / 10A;
- SMD optocoupler isolation, strong driving capability, stable performance; trigger current 5mA;
- Each channel of the module can be set by jumper cap high or low-level trigger;
- Power indicator (green), 8 channels relay status indicator (red)
- Module Power Supply: 12V（Module supply voltage must be DC, and the voltage to be consistent with the relay voltage).
Description
Description:
Electrical parameters:
- Supply voltage: DC5V / 12V
- Trigger mode: High / Low Level Trigger
- Load voltage: DC 30V / AC 250V
- Load current: 10A
- Product weight: 120g
- Size:141.5x50x18.5mm (LxWxH)
- Mounting hole size:136×44.5(LxW)Module Interface:
- DC +: Power supply Positive. (Module supply voltage must be DC, and the voltage to be consistent with the relay voltage).
- DC -: Power supply negative.
- IN1-IN8: According to the setting of each way, it can control the corresponding relay to be high or low.
Relay output:
All interfaces can be directly connected, user-friendly
- NO1 – NO8: relay normally-open interface
- COM1 – COM8: relay common interface
- NC1 – NC8: normally closed relay interface
High / Low Trigger Select :
- S1-S8 is the relay 1-channel to 8-channel high / low trigger selection
- COM and Low connected, the relay is a low-level trigger; COM and High connected. the relay is a high-level trigger.
Package Included:
1×8-Channel Relay Module
Reviews (0)
You must be logged in to post a review.
Shipping & Delivery
Related products
Arduino Ethernet Shield w/o PoE (Wiznet W5100)
(Get A latest Price)
The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100 ethernet chip providing a network (IP) stack capable of both TCP and UDP. The Arduino Ethernet Shield supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet via a standard RJ45 Ethernet jack using the shield.
Arduino Nano V3.0 CH340 Improved Atmega328P USB to TTL with USB cable
Overview:
- Microcontroller: Atmega328
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Digital I/O Pins 14 (of which 6 provide PWM output)
- Analog Input Pins: 6
- DC Current per I/O Pin: 40 mA
- DC Current for 3.3V Pin: 50 mA
- Flash Memory:32 KB (ATmega328) of which 0.5 KB used by bootloader
- SRAM:2 KB (ATmega328)
- EEPROM:1 KB (ATmega328)
- Clock Speed:16 MHz
Arduino UNO R3 with USB cable (ATMEGA 328P)
Specifications:
Microcontroller ATmega328
Operating Voltage 5V
Input Voltage (recommended) 7-12V
Input Voltage (limits) 6-20V
Digital I/O Pins 14 (of which 6 provide PWM output)
Analog Input Pins6
DC Current per I/O Pin 40 mA
DC Current for 3.3V Pin 50 mA
Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader
SRAM 2 KB (ATmega328)
EEPROM 1 KB (ATmega328)
Clock Speed 16 MHz
Length 68.6 mm
Width 53.4 mm
Weight 25 g
Motor Drive Shield (L293D) for Arduino
L293D is a monolithic integrated, high voltage, high current, 4-channel driver
- Can drive 4 DC motors or 2 stepper motors or 2 Servo.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection.
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
- 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 10V DC.
Reviews
There are no reviews yet.