Arduino Shield RAMPS-FD for Arduino Due 3D printer controller
When you use Arduino Due as the controller of your 3D Printer, you may find the RAMPS1.4 is not compatible with DUE.As you know the Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3, the importance is the Atmel SAM3X8E chip used on the Due operates at 3.3V,worse applying 5V to the Due’s inputs will likely damage the chip.
So we create a new RAMPS variant which is compatible with the Due to replace Ramps 1.4.
Description:
Why should I use Ramps-FD instead of Ramps1.4
Compare Ramps-FD with Ramps1.4, the Improvements of Ramps-FD are below
* The RAMPS-FD has other hardware protection, through the jumper cap control motor drive IC
* The RAMPS-FD Much more than Ramps1.4 2-way PWM
* The RAMPS-FD has Larger driving power than Ramps1.4
* The RAMPS-FD ‘POWER has two choices:12v and 24v
Why should I select Arduino DUE instead of Arduino Mega
* CPU operates at 3.3V
* High-current IO pins are capable of 15 mA source, 9 mA sink
* Low-current IO pins capable of 3 mA source, 6 mA sink
* CPU package has an absolute max of 130mA
* The Due has 1 dedicated SPI port, and 4 multipurpose USART/SPI ports. The SPI port is only routed to the 6 pin header used for ICSP on Mega, but this is not used for ICSP on Due
* The Due does not have any EEPROM
* Due has lower power, computing faster and flash, sram bigger than mega2560.
You will need to buy a LCD adapter for RAMPS-FD.
Package List:
1 × RAMPS-FD Shield for Arduino DUE
You must be logged in to post a review.
Related products
Arduino MEGA 2560 R3 (ATMEGA2560-16AU MCU)
Overview
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560 (datasheet). It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega is compatible with most shields designed for the Arduino Duemilanove or Diecimila.
GPS Shield with Data Logger (SD Card) for Arduino UNO +
Leonardo R3 Development Board ATMEGA32U4
Product specifications:
• Controller: ATmega32u4 • Work record: 16 MHz • Working voltage: 5V • Input voltage (recommended): 7-12V • Digital IO port: 20 • PWM channel: 7 • Analog input: 12 • 5V digital / analog port maximum allowable current: 40 mA • 3.3V digital / analog port maximum allowable current: 50 mA • Flash Memory: 32 KB (ATmega32u4) of which 4 KB used by bootloader • SRAM: 2.5 KB (ATmega32u4) • EEPROM: 1 KB (ATmega32u4)
Raspberry Pi 3 Model B (1GB)
SIM900 GPRS/GSM Arduino Shield Development Board (Quad Band)
uLCD-32PTU-Pi (3.2″ Raspberry Pi Display Module for the Raspberry Pi A, B and B+)
| Manufacturer | 4D Systems |
| Type of display | TFT |
| Screen size | 3.2" |
| Display resolution | 240x320 |
| Supply voltage | 5V DC |
| Contrast | 450:1 |
| Luminosity | 250cd/m2 |
| No. of colours | 65k |
| Window dimensions (H x W) | 48.6 x 64.8mm |
| Dimensions | 56.32 x 92.19 x 15.9mm |
| Kind of display | graphical |
| Microcontroller | PICASO |
| Series | Raspberry Pi |
| Viewing angle | 150° |
UNO R3 Sensor Shield V5 Expansion Board For Arduino
- Ready to plug & play.
- It can connect to various modules like sensors, servos, relays, buttons, potentiometers
- Each functional module has buckled port with VCC, GND and Output, which has corresponding port on the Sensor Shield, connected with a plain 2.54mm dual-female cable you may start playing already. Buckled brick cables are like cement for bricks, make the connections easier, secure and more professional looking.
Reviews
There are no reviews yet.