AVR Board UNO PLUS Onboard MCU ATMEGA328P-AU Compatible with Arduino UNO R3 Board Kit Improved & Enhanced Solution Development Board
AVR Board UNO Plus Onboard MCU Atmega328P-AU Compatible With Arduino
Overview:
- Compatible with Arduino UNO R3
- improved & enhanced alternative solution for Arduino UNO R3
- compatible with standard Arduino interface with an additional analog input (A6)
- solder pads provided, supports prototype breadboard
- ICSP interface
Description
Reviews (0)
Be the first to review “AVR Board UNO Plus Onboard MCU Atmega328P-AU Compatible With Arduino” Cancel reply
You must be logged in to post a review.
Shipping & Delivery
Related products
Arduino DUE R3 Board SAM3X8E 32-bit Cortex-M3 Control Board Module
Overview:
Arduino Due Microcontroller Board based on the Atmel SAM3X8E ARM Cortex-M3 CPU. It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pins (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UARTs (hardware serial ports), a 84 MHz clock, an USB OTG capable connection, 2 DAC (digital to analog), 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase buttonARDUINO GEMMA WearAble ATtiny85 Board
Arduino Leonardo, ATmega32U4, USB
Specifications
- Microcontroller: ATmega32u4
- Operating Voltage: 5V
- Input Voltage: 7-12V (recommended)
- Digital I/O Pins: 20
- PWM Channels: 7
- Analog Input Channels: 12
- DC Current per I/O Pin: 40 mA
- Flash Memory: 32 KB (ATmega32u4) of which 4 KB is used for the bootloader
- SRAM: 2.5 KB (ATmega32u4)
- EEPROM: 1 KB (ATmega32u4)
- Clock Speed: 16 MHz
Arduino M0 Pro – ATSAMD21G18 Controller
The Arduino M0 Pro is an Arduino M0 with a step-by-step debugger
Specification:
- 1.Micro Controller:ATSAMD21G18,48pins LQFP
- 2.Working Voltage:3.3V
- 3.Digtal I/O Pin:14,12 Piece PWM and UART
- 4.Analog Input Pin:6,12-status ADC channels
- 5.Analog Output Pin:1,10-status DAC
- 6.Each I/O Pin's Direct Current:7 mA
- 7.Flash Memory:256 KB
- 8.SRAM:32 KB
- 9.EEPROM:Through Simulation Highest is 16KB
- 10.Clock Spead:48 MHz
- 11.L*W:2.7*2.1 inches
- 12.External Power:5V1A~2A
- 13.Weight:70g
Arduino Pro Mini – 3.3V/8MHz, 5V/16MHz (ATMEGA328)
Features:
• ATmega328 running at 8MHz with external resonator (0.5% tolerance) • Low-voltage board needs no interfacing circuitry to popular 3.3V devices and modules (GPS, accelerometers, sensors, etc) • USB connection off board • Supports auto-reset • 3.3V regulator • Reverse polarity protected • DC input 3.3V up to 12V • On board Power and Status LEDsLeonardo R3 Development Board ATMEGA32U4
Product specifications:
• Controller: ATmega32u4 • Work record: 16 MHz • Working voltage: 5V • Input voltage (recommended): 7-12V • Digital IO port: 20 • PWM channel: 7• Analog input: 12• 5V digital / analog port maximum allowable current: 40 mA• 3.3V digital / analog port maximum allowable current: 50 mA• Flash Memory: 32 KB (ATmega32u4) of which 4 KB used by bootloader• SRAM: 2.5 KB (ATmega32u4)• EEPROM: 1 KB (ATmega32u4)WiFly RN-171
Features:
- Ultra low power for battery powered applications
- Firmware configurable transmit power: 0dBm to +12dBm
- Hardware interfaces: UART
- Supports Adhoc and infrastructure networking modes
- User programmable GPIO & ADCs
- Real-time clock for time-stamping, auto-sleep, and auto-wakeup modes
- Run directly from batteries or regulated power supplies
- Configuration over serial or wireless interface using simple ASCII commands
- Over the air firmware upgrade
- Secure Wi-Fi authentication schemes (WEP/WPA/WPA2)
- Full onboard TCP/IP stack (no external drivers required)
XBee 1mW Wire Antenna
This is the very popular 2.4GHz XBee module from Digi. These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
Reviews
There are no reviews yet.