BPI Camera Module OV5640 Chipset (5M pixel)
The camera V3 module is specifically designed for the BPI-M3. It includes CMOS sensor module OV5640 (5M Pixel)
- OV5640 banana chip pi similar camera for raspberry pi csi camera
- Banana pi camera, use ov5640 (500w) chip inside
Description:
Product Specifications:
| Product name | Banana PI Camera Module |
| Product description | High definition camera module for BananaPi card via the CSI connector designed specifically for interfacing tocameras. Provides high sensitivity, low crosstalk and low image noise capture in a small and light design. |
| image sensor | Omnivision 5640 CMOS image sensor in a self-fouces modules with integral IR filter (650 ± 10nm) |
| still resolution | 5 Megapixels |
| active array format | 2592 × 1944 |
| Max frame rate | 1080p 30fps @ 24Mhz |
| image formats | JPEG PNG YUV420 RGB888 |
| Video formats | Raw h.264 |
| connection to Banana Pi | 40 Pin FPC Interface for Camera Sensor (CSI-0) |
| image control functions | automatic exposure control (AEC)
automatic white balance (AWB) Automatic calibration black level (ABLC) automatic band filter mirror and vibration |
| Temp range | operation: -30 ° C to 70 ° C
A stable image: 0 ° C to 50 ° C |
| lens size | 1/4 & Prime; |
| Dimension | 36 × 32 × 10mm |
| I2C address | 0x78 |
| weight | 8g |
Banana pi CSI Camera Connector
CSI Camera Connector is an FPC-pin connector that allows you to connect external camera module with a correct signal mapping pin.
You must be logged in to post a review.
Related products
Arduino Pro Mini – 3.3V/8MHz, 5V/16MHz (ATMEGA328)
Features:
• ATmega328 running at 8MHz with external resonator (0.5% tolerance) • Low-voltage board needs no interfacing circuitry to popular 3.3V devices and modules (GPS, accelerometers, sensors, etc) • USB connection off board • Supports auto-reset • 3.3V regulator • Reverse polarity protected • DC input 3.3V up to 12V • On board Power and Status LEDs
Arduino Pro Mini Atmega168 (3.3V/ 8MHz, 5V/16MHz)
Features:
- 14 Digital input / output ports RX, TX D13, D12
- 8 analog input port A0 to A7
- The TTL level serial transceiver port RX / TX
- 4.6 PWM ports, D3,, D5 , D6, D9, D10, D11
- Using Atmel Atmega168P microcontroller
- Supports serial download (TTL)
- Support for external 5V ~ 12V DC power supply
- Support 9V battery-powered
- clock frequency 16MHz
Package includes:
-
1x Arduino Pro mini Atmega168 module board
- 3x header pin rows
Motor Drive Shield (L293D) for Arduino
- Can drive 4 DC motors or 2 stepper motors or 2 Servo.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection.
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
- 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 10V DC.
Raspberry Pi Compute Module 3 – 4Gbytes eMMC Flash
Raspberry Pi Calculation Module 3
Raspberry Compute Module 3 is for designers who prefer Raspberry Pi3 functionality but require a smaller form factor (67.6 mm X 31 mm) for their embedded design. These modules are DDR2-SODIMM, mechanically compatible system-on-a-chip (SoM) that includes a BCM2837 processor system-on-a-chip (SoC) with 1 GB of LPDDR2 RAM and 4 GB of eMMC flash. In addition, these modules have an additional input/output (I/O) interface in addition to the Raspberry Pi Model A/B board.
Reviews
There are no reviews yet.