CJMCU-6002 (Sun Ultravoilet Spectral Intensity Sensor)
Solar Ultraviolet spectral sensor of intensity of analog voltage
Power range: +2.7-5.5VDC
Output signal: analog voltage
The CJMCU-6002 UV sensor module expands the photosensitivity spectrum. It uses an ultraviolet photodiode to detect light in the 240 – 370nm range (including most of the spectra of UVA and UVB ).
Related products
AMG8834
Temperature Sensor Digital, Infrared (IR) 14-SMD Module
Product Specifications
| Sensor type | Infrared array sensor | |
| Maximum output current | 10mA | |
| Sensing distance | 7m | |
| Switch mode | digital | |
| Installation type | Surface mount | |
| Number of pins | 14 | |
| Maximum supply current | 4.5 mA | |
| size | 11.6 x 8 x 4.3mm | |
| height | 4.3mm | |
| length | 11.6mm | |
| series | Grid-EYE | |
| Maximum working temperature | +80 °C | |
| Maximum operating supply voltage | 5 V DC | |
| Minimum operating temperature | -20 °C | |
| width | 8mm |
KY-028 -Temperature sensor module (Digital)
Product Features:
- Using the NTC thermistor sensor , good sensitivity.
- The comparator output signal is clean, good waveform , driving ability , more than 15mA.
- Adjust the temperature distribution position detection threshold.
- The working voltage: DC 3.3V-5V.
- The output format : digital switching outputs ( 0 and 1 )
- A fixed bolt holes for easy installation.
- Using a wide voltage LM393 comparator.
MQ-5 (Gas Sensor module LPG, Natural Gas, Coal Gas)
Overview
- Sensitive for LPG, natural gas, coal gas
- An increase in the output voltage along with the concentration of the measured gases
- Rapid reaction and recovery
- Adjustable sensitivity
- Output indicator
Gas Sensor type |
Sensitive gas |
Application |
| MQ-135 Gas Sensor | Benzene, alcohol, smoke | Air Quality Monitoring |
| MQ-2 gas sensor | HBO, propane, hydrogen | Gas leak detector |
| MQ-3 gas sensor | Alcohol, ethanol | Carbon alcohol, Breathalyzer |
| MQ-5 Gas Sensor | CIS, natural gas, coal gas | Gas leak detector |
| MQ-7 gas sensor | Carbon monoxide | Carbon Monoxide Monitor |
MQ-8 (Hydrogen Gas Sensor Module)
MQ-8 Sensor Information: sensitive material MQ- 8 gas sensors used in clean air, low conductivity tin oxide (SnO2). When there is an environment in which the combustible gas sensor, conductivity sensor with increasing concentration of combustible gases in air increases. Use simple circuit can convert the change in conductivity of the gas concentration corresponding to the output signal. MQ-8 hydrogen gas sensor of high sensitivity monitoring of other hydrogen-containing gas is also very good. The sensor can detect a variety of hydrogen-containing gas, in particular, city gas, is a low-cost sensor suitable for a variety of applications.
Sharp IR Long Range Sensor – 20 cm to 150 cm
- Infrared range finder 20cm(~8") to 150cm (~60")
- Analog interface
T000220 (Arduino TinkerKit Touch Sensor Module)
- Based on a QT 100A single touch controller
- On-board-signal amplifier
- Green LED for correct power indication
- Yellow LED whose brightness depends on the values output by the module
TTP229-LSF (Capacitive Touch Keypad Module)
Features:
- On board 8 capacitive touch keys and 1 linear capacitive sensor
- Features TONTEK TonTouch touch pad detector IC TTP229-LSF, supports up to 16 keys with adjustable sensitivity and built-in LDO
- The system recalibrates automatically when all keys are not detected touch more than about 4 seconds
- Customizable functions:
- 8 keys or 16 keys option
- 8 individual outputs or batch production
- Single-key or multi-kye feature
- Sampling rate and duration of sampling in sleep mode
- The maximum key is on time
Reviews
There are no reviews yet.