Back to products
ESP8266 ESP-05 Remote Serial Port WiFi Transceiver Wireless Module
Original price was: ₨500.00.₨380.00Current price is: ₨380.00.
ESP8266 ESP-12E UART Wi-Fi Shield for Arduino UNO & MEGA
Fully compatible with Uno, Mega, etc. using standard pin interface spacing .(unless standard size, such as Nano, Mini)
Description
ESP8266 ESP-12E Wi-Fi Technical Specifications:
- 802.11 b / g / n wireless standards;
- STA / AP modes support ;
- TCP / IP protocol stack, One socket;
- Supports standard TCP / UDP Server and Client;
- Supports serial port baud rate configuration: 1200/2400/4800/9600/19200/38400/57600/74800/115200 bps;
- Supports serial data bits: 5/6/7/8 bits;
- Supports serial parity: none;
- Supports serial stop bits: 1/2 bit;
- Pin-compatible with Arduino UNO, Mega;
- Arduino Pinout 2/3/4/5/6/7/8/9/10/11/12/13;
- ESP8266 GPIO Pinout 0/2/4/5/9/10/12/13/14/15/16 / ADC / EN / * UART TX / UART RX;
- KEY button: modes configuration;
- Dual-Ports DIP switches: switching Arduino and ESP8266;
- WiFi operation current: continuous transmission operation: ≈70mA (200mA MAX), idle mode: <200uA;
- Serial WiFi transmission rate: 110-460800bps;
- Temperature: -40℃ ~ + 125 ℃;
- Humidity: 10%-90% non-condensing;
- Weight: about 20g (0.7oz);
The Shield has two LEDs. Red LED is donated to power supply. Blue LED is a multi-functional LED and its functions are:
Reviews (0)
You must be logged in to post a review.
Shipping & Delivery
Related products
Motor Drive Shield (L293D) for Arduino
L293D is a monolithic integrated, high voltage, high current, 4-channel driver
- Can drive 4 DC motors or 2 stepper motors or 2 Servo.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection.
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
- 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 10V DC.
U-BLOX NEO-6M module (GY-GPS6MV2)
This GPS is a very capable GPS for the price and size. Compatible with UART capable devices including Arduino, Raspberry Pi, MSP430, and MSP432.
Power the module and it will automatically acquire satellite signals and a position fix. Once it has a position fix the module will blink the on board LED. This LED will continue to blink while the module has a position fix.
The Product contains the following parts;
- 1 — u-blox NEO-6M GY-GPS6MV2 GPS module with on board EEPROM
- 1 — GPS antenna
- 1 — 1x4 male header
XBee 1mW Wire Antenna
Description:
This is the very popular 2.4GHz XBee module from Digi. These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
- 3.3V @ 50mA
- 250kbps Max data rate
- 1mW output (+0dBm)
- 300ft (100m) range
- Wire antenna
- Fully FCC certified
- 6 10-bit ADC input pins
- 8 digital IO pins
- 128-bit encryption
- Local or over-air configuration
- AT or API command set
XBee 1mW Wire Antenna
This is the very popular 2.4GHz XBee module from Digi. These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
Reviews
There are no reviews yet.