GY-485-44009 (High Precision Light Intensity Sensor Module)
GY-MODBUS-44009 MODBUS PROTOCOL RS485 TRANSMISSION LIGHT INTENSITY SENSOR MODULE.
General Features:
100% Brand New and High Quality.
1. Type: GY-485-44009 Module
2. Diameter: 27mm
3. High Precision
4. Light Intensity Light Intensity Sensor
Compare
Related products
CJMCU-175 (Digital Temperature Sensor Module)
General Features:
CJMCU-175 Digital Temperature Sensor TMP175 27 Address
Digital output: SMBusTM, two-wire and I2C interface compatibility
Resolution: 9 to 12 digits, user selectable
Wide supply voltage range: 2.7V to 5.5V
TMP175 allowing up to 27 devices on a bus member.
It is a negative temperature desired coefficient thermistor (NTC) and positive temperature coefficient (PTC) for generation
The device provides a typical Ā±1Ā°C accuracy without calibration or external component signal conditioning .
The on-chip 12-bit analog -to- digital converter (ADC) provides resolution down to 0.0625Ā°C.
Motion Detecting Module- Zilog ePIR
Zilog's ePIR is a fully functional motion-detecting single-board computer (SBC). Combined on this board are a Z8 Encore! XP MCU, and a Murata passive infrared (PIR) sensor, which is shielded by a Fresnel lens. Taking advantage of the processing capabilities of the Z8 MCU, the ePIR uses a powerful new statistical processing method to provide exceptional motion detection performance.
MQ-7 (Carbon Monoxide Gas Sensor Module)
MQ-7 Carbon Monoxide Gas Sensor Module is used to detect Carbon Monoxide (CO) concentration, it can detect CO-gas concentrations anywhere from 20 to 2000ppm. This sensor has a high sensitivity and fast response time. The module outputs a voltage from 0 to 5V relative to the CO concentration. The sensor can operate at temperatures from -10 to 50Ā°C and consumes less than 150 mA at 5 V.
SHT31 (Digital Temperature and Humidity Sensor Module)
General Features:
- Highly reliable, accurate and quick response time
- I2C interface
- Well calibrated, linearized, compensated for digital output
- Highly abstracted development library
- Input voltage (VCC): 3.3 volts or 5 volts
- I/O Logic Level : 3.3 volts or 5 volts based on VCC
- Operating Current : 100 Ī¼A
- Operating Temperature : -40ā125 ā
- Temperature Sensor Range : -40ā125 ā, with Ā±0.3Ā°C accuracy
- Humidity Sensor Range : 0% - 100%(Relative Humidity), with Ā±2% accuracy
- Sensor Chip : SHT31
- I2C
T000220 (Arduino TinkerKit Touch Sensor Module)
This TinkerKit sensor is a touch sensitive device that provides an output when it detects skin contact. The sensor is connected to an Arduino board via a TinkerKit Shield to form part of the TinkerKit modular prototyping system.
- Based on a QT 100A single touch controller
- On-board-signal amplifier
- Green LED for correct power indication
- Yellow LED whose brightness depends on the values output by the module
TTP 223B (Touch Thumb Sensor Module)
Product description:
This is a simple touch sensor module. You can use it to replace a traditional push button. Using the TTP223 touch detector IC It measures the capacitance of a metallic pad. It can detect the change in capacitance when a finger is near it. This is the same technology used in the iPhone touch screen.This little sensor can "feel" people and metal touch and feedback a high/low voltage level. Even isolated by some cloth and paper, it still can feel the touch. And the sensitivity well decrease as isolation get thick.
Reviews
There are no reviews yet.