-8%
MQ-4 (Methane Gas Sensor module for Arduino)
Original price was: ₨280.00.₨220.00Current price is: ₨220.00.
MQ-6 LPG Gas Sensor Module
Original price was: ₨360.00.₨300.00Current price is: ₨300.00.
MQ-5 (Gas Sensor module LPG, Natural Gas, Coal Gas)
Original price was: ₨400.00.₨370.00Current price is: ₨370.00.
Overview
- Sensitive for LPG, natural gas, coal gas
- An increase in the output voltage along with the concentration of the measured gases
- Rapid reaction and recovery
- Adjustable sensitivity
- Output indicator
Gas Sensor type |
Sensitive gas |
Application |
| MQ-135 Gas Sensor | Benzene, alcohol, smoke | Air Quality Monitoring |
| MQ-2 gas sensor | HBO, propane, hydrogen | Gas leak detector |
| MQ-3 gas sensor | Alcohol, ethanol | Carbon alcohol, Breathalyzer |
| MQ-5 Gas Sensor | CIS, natural gas, coal gas | Gas leak detector |
| MQ-7 gas sensor | Carbon monoxide | Carbon Monoxide Monitor |
Description
Specifications
- Power: 2.5V ~ 5.0V
- Size: 40.0 mm * 21.0 mm
- Mounting Holes Size: 2.0 mm
Applications
- Gas leak detector
How to Use
In case of working with MCU:
- VCC ↔ 2.5 V ~ 5.0 V
- GND ↔ power supplies
- Aout ↔ MCU. io (analog output)
- DOUT ↔ MCU. io (digital output)
Reviews (0)
You must be logged in to post a review.
Shipping & Delivery
Related products
CJ1WTS562 (Temperature Sensor Module Screw Terminal Connection)
Omron Temperature sensor module is suitable for use with cj1 series programmer controllers
Highlights/Features:
Omron Temperature sensor module is suitable for use with cj1 series programmer controllers These temperature sensor units are classified as digital I/O units when considering I/O allocations and will take digital I/O points from the total allocation for a CJ1M CPU. The number of I/O points is DIP switch selectable as follows; configured for 1 - 3 inputs takes 48 digital I/O points, configured for 4 inputs takes 64 digital I/O points and configured for 5 - 6 inputs takes 96 digital I/O points.
CJMCU-175 (Digital Temperature Sensor Module)
General Features:
CJMCU-175 Digital Temperature Sensor TMP175 27 Address
Digital output: SMBusTM, two-wire and I2C interface compatibility
Resolution: 9 to 12 digits, user selectable
Wide supply voltage range: 2.7V to 5.5V
TMP175 allowing up to 27 devices on a bus member.
It is a negative temperature desired coefficient thermistor (NTC) and positive temperature coefficient (PTC) for generation
The device provides a typical ±1°C accuracy without calibration or external component signal conditioning .
The on-chip 12-bit analog -to- digital converter (ADC) provides resolution down to 0.0625°C.
MQ-2 (Smoke sensor-HBO, LPG, Alcohol, Propane, Hydrogen, Methane and Carbon Monoxide)
MQ2 Smoke Gas Sensor Module is a general purpose gas sensor and this Sensor is used to detect the gas leakage of LPG, Smoke, Alcohol, Propane, Hydrogen, Methane and Carbon Monoxide concentrations ranging from 200 to 10000 ppm.
- MQ-2 Gas Sensor Module LPG, Smoke, Alcohol, Propane, Hydrogen, Methane and Carbon Monoxide Detection
- Dual signal output (analog output, and TTL level output)
- The gas, natural gas, city gas, smoke better sensitivity
- With a long service life and reliable stability
- Rapid response and recovery characteristics
MQ-8 (Hydrogen Gas Sensor Module)
MQ-8 Sensor Information: sensitive material MQ- 8 gas sensors used in clean air, low conductivity tin oxide (SnO2). When there is an environment in which the combustible gas sensor, conductivity sensor with increasing concentration of combustible gases in air increases. Use simple circuit can convert the change in conductivity of the gas concentration corresponding to the output signal. MQ-8 hydrogen gas sensor of high sensitivity monitoring of other hydrogen-containing gas is also very good. The sensor can detect a variety of hydrogen-containing gas, in particular, city gas, is a low-cost sensor suitable for a variety of applications.
Sharp IR Long Range Sensor – 20 cm to 150 cm
- Infrared range finder 20cm(~8") to 150cm (~60")
- Analog interface
TTP 223B (Touch Thumb Sensor Module)
Product description:
This is a simple touch sensor module. You can use it to replace a traditional push button. Using the TTP223 touch detector IC It measures the capacitance of a metallic pad. It can detect the change in capacitance when a finger is near it. This is the same technology used in the iPhone touch screen.This little sensor can "feel" people and metal touch and feedback a high/low voltage level. Even isolated by some cloth and paper, it still can feel the touch. And the sensitivity well decrease as isolation get thick.
Reviews
There are no reviews yet.