MS5611 (High Resolution Atmospheric Pressure Module)
1. MS5611 module (atmospheric pressure module).
2. Chips: MS5611.
3. Chip built-in 24bit AD converter.
4. Immersion Gold PCB, high quality, machine welding process to ensure quality.
5. Power supply: 3~5V (internal low dropout regulator).
6. Communication modes: standard the I2C / SPI communication protocol.
The MS5611-01BA is a new generation of high resolution altimeter sensors from MEAS Switzerland with SPI and I2C bus interface. This barometric pressure sensor is optimized for altimeters and variometers with an altitude resolution of 10 cm. The sensor module includes a high linearity pressure sensor and an ultra low power 24 bit ΔΣ ADC with internal factory calibrated coefficients. It provides a precise digital 24 Bit pressure and temperature value and different operation modes that allow the user to optimize for conversion speed and current consumption.
A high resolution temperature output allows the implementation of an altimeter/thermometer function without any additional sensor. The MS5611-01BA can be interfaced to virtually any microcontroller. The communication protocol is simple, without the need of programming internal registers in the device.
Features:
- MS5611-01BA High Resolution Atmospheric Pressure Sensor
- Range: 10mbar – 1200mbar
- ADC: 24 bit
- Resolution: 10cm
- Interface: I2C and SPI
- Power supply : 3V-5V (internal low dropout regulator).
- Logic level conversion on board – so save for 5V and 3V systems
You must be logged in to post a review.
Related products
BMP280 (I2C/SPI Digital Barometric Pressure Sensor Module for Arduino)
Features:
- Pressure range: 300 ~ 1100hPa (altitude 9000 m ~ -500 m); - Working voltage: 1.71 - 3.6VDC; - Low power consumption: 4μA; - High precision: at low-power mode, the resolution is 0.06hPa (0.5 meters); - Temperature output; - Communication interface: I2C or SPI; typical application: - GPS precise navigation (dead reckoning, the upper and lower bridge detection, etc.); - indoor and outdoor navigation; - The weather forecast; - The vertical velocity indication (rise / sink speed); Note: You need to add 5V to 3.3V level converter circuit between Arduino UNO R3 and the module.
CJ1WTS562 (Temperature Sensor Module Screw Terminal Connection)
Highlights/Features:
Omron Temperature sensor module is suitable for use with cj1 series programmer controllers These temperature sensor units are classified as digital I/O units when considering I/O allocations and will take digital I/O points from the total allocation for a CJ1M CPU. The number of I/O points is DIP switch selectable as follows; configured for 1 - 3 inputs takes 48 digital I/O points, configured for 4 inputs takes 64 digital I/O points and configured for 5 - 6 inputs takes 96 digital I/O points.
DHT22- (Temperature and humidity sensor)
Product description:
The DHT22 module is designed to measure the temperature and humidity of the atmosphere. The difference from the younger model (DHT11), The DHT22 has a wide range and a high precision determination of temperature and humidity. The sensor works on the OneWire bus, which makes it possible to connect it to the Arduino only three wires ( two of which are POwer supply). Low power consumption allows you to install it on stand-alone devices.
GO2Y0A21YK
GO2Y0A21YK
Infrared distance measuring sensor (including dedicated data line)Technical Parameters:
- Model : GP2Y0A21YK (GP2D12 upgrade)
- Voltage: 4.5-5. 5V
- Current: 33-40mA
- Port: Analog
- Detection distance: 10-80cm
- Data line: 3P 20cm
- Wire: 24# American standard line
- Interface: 3P DuPont SVG compatible Arduino sensor expansion board
T000220 (Arduino TinkerKit Touch Sensor Module)
- Based on a QT 100A single touch controller
- On-board-signal amplifier
- Green LED for correct power indication
- Yellow LED whose brightness depends on the values output by the module
TMP006 (Contact-less Infrared Temperature Measurement)
Features:
- 20mm x 20mm (board w/o headers)
- Uses I2C 7-bit addresses between 0x40 and 0x47, selectable with jumpers
- Interface Type : I2C Arduino driver module
Reviews
There are no reviews yet.