You must be logged in to post a review.
SW-18010P (Vibration Sensor Module)
1. when the product does not work, the vibrating switch is turned off, the output of the high output, the green light does not shine through
2. when the product shock, vibration switch is turned on instantly, output low output, green indicator light
3. the output can be directly connected to the microcontroller through the microcontroller to detect high and low, thereby determining whether there is a vibration in the environment, playing a role in the police
Pin description:
- VCC: 3-5V DC
- GND: min/ground/gnd
- DO: digital output (sensitivity can be controlled with the potentiometer)
- AO: analog output
Categories: Sensor Modules, Vibration Sensor Modules
Related products
CJ1WTS562 (Temperature Sensor Module Screw Terminal Connection)
Omron Temperature sensor module is suitable for use with cj1 series programmer controllers
Highlights/Features:
Omron Temperature sensor module is suitable for use with cj1 series programmer controllersThese temperature sensor units are classified as digital I/O units when considering I/O allocations and will take digital I/O points from the total allocation for a CJ1M CPU. The number of I/O points is DIP switch selectable as follows;configured for 1 - 3 inputs takes 48 digital I/O points, configured for 4 inputs takes 64 digital I/O points and configured for 5 - 6 inputs takes 96 digital I/O points.KY-028 -Temperature sensor module (Digital)
Product Features:
- Using the NTC thermistor sensor , good sensitivity.
- The comparator output signal is clean, good waveform , driving ability , more than 15mA.
- Adjust the temperature distribution position detection threshold.
- The working voltage: DC 3.3V-5V.
- The output format : digital switching outputs ( 0 and 1 )
- A fixed bolt holes for easy installation.
- Using a wide voltage LM393 comparator.
Motion Detecting Module- Zilog ePIR
Zilog's ePIR is a fully functional motion-detecting single-board computer (SBC). Combined on this board are a Z8 Encore! XP MCU, and a Murata passive infrared (PIR) sensor, which is shielded by a Fresnel lens. Taking advantage of the processing capabilities of the Z8 MCU, the ePIR uses a powerful new statistical processing method to provide exceptional motion detection performance.
MQ-2 (Smoke sensor-HBO, LPG, Alcohol, Propane, Hydrogen, Methane and Carbon Monoxide)
MQ2 Smoke Gas Sensor Module is a general purpose gas sensor and this Sensor is used to detect the gas leakage of LPG, Smoke, Alcohol, Propane, Hydrogen, Methane and Carbon Monoxide concentrations ranging from 200 to 10000 ppm.
- MQ-2 Gas Sensor Module LPG, Smoke, Alcohol, Propane, Hydrogen, Methane and Carbon Monoxide Detection
- Dual signal output (analog output, and TTL level output)
- The gas, natural gas, city gas, smoke better sensitivity
- With a long service life and reliable stability
- Rapid response and recovery characteristics
MQ-6 LPG Gas Sensor Module
This is a simple-to-use liquefied petroleum gas (LPG) sensor, suitable for sensing LPG (composed of mostly propane and butane) concentrations in the air. The MQ-6 can detect gas concentrations anywhere from 300 to 10000ppm. This sensor has a high sensitivity and fast response time. The sensor’s output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater coil with 5V, add a load resistance, and connect the output to an ADC.
TTP 223B (Touch Thumb Sensor Module)
Product description:
This is a simple touch sensor module. You can use it to replace a traditional push button. Using the TTP223 touch detector IC It measures the capacitance of a metallic pad. It can detect the change in capacitance when a finger is near it. This is the same technology used in the iPhone touch screen.This little sensor can "feel" people and metal touch and feedback a high/low voltage level. Even isolated by some cloth and paper, it still can feel the touch. And the sensitivity well decrease as isolation get thick.
TTP224 (4 Channel Digital Capacitive Touch Sensor Button Switch Module For Arduino)
TTP229-LSF (Capacitive Touch Keypad Module)
Features:
- On board 8 capacitive touch keys and 1 linear capacitive sensor
- Features TONTEK TonTouch touch pad detector IC TTP229-LSF, supports up to 16 keys with adjustable sensitivity and built-in LDO
- The system recalibrates automatically when all keys are not detected touch more than about 4 seconds
- Customizable functions:
- 8 keys or 16 keys option
- 8 individual outputs or batch production
- Single-key or multi-kye feature
- Sampling rate and duration of sampling in sleep mode
- The maximum key is on time
Reviews
There are no reviews yet.