XGecu TL866II Plus USB (Universal) Programmer for 15000+IC SPI Flash NAND EEPROM MCU PIC AVR+10 Adapter+IC Puller+ Component Storage box

TL866II Plus programmer highlights the advantages:

1. Support one computer with 4 programmers to burn at the same time. 
2. Small size, high density, low power consumption, high performance, a comprehensive programmer that is really hot. 
3. All chips do not need an external power supply, and their low power consumption ensures that the USB port can provide enough power. 
4. Internal 40-pin overvoltage protection, strong VPP, VCC four-level overcurrent protection. Doing a short circuit does not reset the PC or the programmer. 
5. Wide range of chip 15000+ support, support for serial series, parallel series 40/44/48PIN large capacity FLASH. 
6. Unique serial programming ICSP interface, supporting serial download and high-speed parallel high-voltage programming. Note: The TL866CS does not support ICSP interface programming. 
7. Test 74/54 CMOS4000 series integrated circuits. Can be located to the door circuit error. 
8. The chip serial number function is complete and practical. 
9. Originally support AVR microcontroller with internal RC correction byte Calibration for chip mass production operation. The brute-forced software cannot be run directly on another chip of the same model. 
10. Automatically detect poor chip pin contact or mis-insertion to avoid damage to the device.

High speed programming:

Built-in high-performance, high-capacity USB interface micro-controller, communication speed 12Mbps, with (for each chip) well-designed programming algorithms and USB high-speed communication. It may be the fastest one in the integrated development programmer, which is already in line with the needs of small batch rapid production. Compared with similar products, the chip programming speed is several times faster, even 10 times or more, 4Mbits parallel FLASH ROM, the programmer programming (erasing, writing, verifying total time) only takes about 36 seconds, reading and writing a 32MB TE28F320 only needs 32+79 seconds, and most of the parallel FLASH chip programming simultaneously check, found that the error can terminate the programming immediately, read and write a 8Mbits serial 25P80 only 9.3 seconds (read) + 1.7s (write) time . The 64MB chip is almost 14.5 seconds + 69 seconds. Supports large capacity 25 series chips in common 8PIN and 16PIN packages. The same computer can be connected to 4 programmers for mass production.

Ultra low power consumption:

The entire programmer uses ultra-low-power chips and is powered by a USB interface. The station is a comprehensive programmer that does not require an external power supply for all chip programming. The measured power consumption is less than 20mA, (7mA when not programming, the power consumption is 5mA for each LED power indicator, and each component is designed to work in the micro power state by default.), the power loss rate during programming Less than 20%. Enables the programmer to provide superior VCC VPP programming current through the USB interface. It provides enough programming power for all programmable chips (up to 2 watts of programmed power output, and it is impossible for a chip to require 2 watts of power programming). And even if the programmer continuously programs the chip for a long time, you can hardly feel the programmer has heat.

Super portable performance:

The size of the world is small, the size of the outer dimensions is 10cm*6cm*2.5cm, only the size of the driver’s license. In addition, due to the ultra-low power consumption, the external power supply is eliminated, and the portable performance is superior.

Programmed programming power supply:

The VPP and VCC programming voltages are independently programmed, with programmable VCC from 1.8 to 6.5V and VPP from 1.8V to 18V powered chips. The power supply is multi-stage LC filtered with minimal ripple.

Over-voltage and over-current protection:

The programmer VCC VPP power supply has independent 3-level over-current protection inside, and the first-level software automatically cuts off the power supply protection. VPP over-voltage protection is provided for each 40P programming socket pin. It effectively prevents the external pin from being short-circuited by the wrong chip or other reasons. During programming, the VPP high voltage 窜 returns to the inside of the programmer and damages the programmer. A short circuit to any external bad condition will not damage the programmer and effectively protect the programmed chip. 
When a short time occurs, the programmer turns off the programming power supply VPP and VCC at 100 uSec and sends a message to the application. Due to the multi-stage over-current protection, the programmer and PC will never be reset when shorted.

40PIN Socket:

One of the 40PIN quasi-pins. When all the chips are programmed, no chip needs to be shifted or turned, the chip is unified forward, and the programming socket handle is placed in the direction of PIN1, which is more in line with the design habits of the designer.

Super upgrade function:

Built-in hardware firmware upgrade function, programming timing is completely controlled by the microcontroller firmware. It can guarantee the update of your programmer firmware FLASH and application software. Upgrade to download the upgrade program via the Internet and upgrade yourself.

Chip serial number secondary development function:

The programmer has built-in multiple automatic numbering functions. You can use a custom algorithm to implement arbitrary serial numbers through the DLL dynamic library. This feature allows you to generate an identification message for each chip during mass production. The logo can also be encrypted with a custom algorithm to protect your product rights more effectively.

Unique serial programming interface ICSP:

While programming through the 40PIN socket, the programmer also has an ICSP serial programming port. For chips that can be serially programmed in-circuit, you can select the ICSP interface to program the MCU on the target board, the wiring method of the ICSP port, and the program with high-definition picture prompts. This makes it easy to update the chip that has been soldered on the board. ( :ICSP now supports 24/25/93A series serial EEPROM, TMEM89S51, 52, ATMEGAxxx AVR full range and MICROCHIP PIC10Fxxx 12Fxxx 16Fxxx 18Fxxx full range, Xinmao SYNCMOS SM59Dxx/SM59Rxx full range of chips for online serial programming. Other more The MCU supporting serial online programming is increasing. The 6 lines of ICSP of this programmer, except one ground GND, lead to full-function I2C, SPI and UART serial bus, suitable for various serial communication. And each line can give VCC, VPP or GND of super high current.

Superior performance 54/74F/LS/HC CMOS4000 series integrated circuit comprehensive function test

A development programmer that can test common logic integrated circuits, test errors that can be located to logic gates, and test any possible input combinations of integrated circuits.

Programmer self-test function:

The programmer can self-check the VPP VDD GND and input and output signals of each pin, and internally short-circuit the VPP and VCC overcurrents (while adding a VPP VCC and GND to a PIN pin for a strong current short circuit). Check operation.

AVR single-chip one-to-one soft encryption:

The AVR micro-controller has an RC Calibration (correction byte). One byte of this byte value may be the same and cannot be modified. The MCU software can read the value, and determine the value to determine whether the code is used on another chip. The custom encryption algorithm can make the brute force cracker unable to use it directly. If the encryption algorithm is complex enough, it is not easy to believe that it is necessary to crack. But “encryption” poses a problem for developers. Each chip is different. If the algorithm is complex, it is impossible to manually compile the original code one by one. The programmer can automatically read in the RC byte before programming. The developer can get the value of the byte in the DLL dynamic function, and then automatically calculate the encrypted data into the memory according to the value according to your requirements. Mass production. (The installation package contains an example of ATMEGA8 detailed encryption for reference)

The operation interface has been carefully designed to fully comply with the operating habits of the Windows series of software, built-in binary editor, comparable to professional pure editing software. It can directly read and write the BIN file, HEX file, JED and other format files. A complete and practical engineering model makes batch production more convenient and safe.